Go Back   Rangefinderforum.com > Cameras / Gear / Photography > Classic Film RangeFinders & Other Classics > SLRs - the unRF

SLRs - the unRF For those of you who must talk about SLRs, if only to confirm they are not RF.

Reply
 
Thread Tools Search this Thread Display Modes

Any Nikon FE+MD12 experts ?
Old 4 Weeks Ago   #1
Ste_S
Registered User
 
Ste_S is offline
Join Date: Aug 2017
Posts: 205
Any Nikon FE+MD12 experts ?

Having trouble using a MD12 in conjunction with an FE.

Meter doesn't turn on with the MD12 connected.
Pressing the shutter button on the MD12 locks the mirror, turning to M90 releases it.
FE+MD12 work at M90 in both s and c modes, but the meter still doesn't turn on.
The FE works fine without the MD12 connected.
Batteries seem ok, although I haven't replaced with fresh in both units - which us a starting point i guess

Any ideas ?
  Reply With Quote

Old 4 Weeks Ago   #2
Timmyjoe
Registered User
 
Timmyjoe's Avatar
 
Timmyjoe is offline
Join Date: Jan 2009
Location: Chicago, IL
Posts: 2,999
Don't have an FE but have been using MD-12's with FM2N's for over twenty years and all I can say is the MD-12 is "iffy" even on it's best days. And they haven't gotten better over time.

Have had all kinds of weird episodes with the FM2N when an MD-12 is attached. Mostly it just stops working. Camera freezes, shutter won't fire, film won't advance. Have to turn off MD-12 and remove it from camera (just turning it off doesn't work), manually advance FM2N, fire the shutter, then reattach MD-12 and turn back on. Sometimes that fixes it, sometimes not. And then it might work for weeks with no problems, then screw up again. Pretty frustrating.

Best,
-Tim
__________________
http://www.timcarrollphotography.com

New Photo Books
Sturgis Stories
& Scenes From Sturgis
now available
  Reply With Quote

Old 4 Weeks Ago   #3
Paulbe
Registered User
 
Paulbe is offline
Join Date: Jun 2005
Location: Suwanee. GA
Posts: 1,473
Agree fully with Tim--MD-12s are bizarre under good circumstances. And I know 25 folks will post and say they have had nothing but mystical experiences with the MD-12--but I have not...
Paul
  Reply With Quote

Old 4 Weeks Ago   #4
Larry H-L
Registered User
 
Larry H-L is offline
Join Date: May 2005
Posts: 597
Quirky at best. I can’t exactly remember the sequence, but it goes something like this... remove MD-12, fire and recock camera, advance lever “in.” Turn MD-12 power switch on. Using a penny, short out the two left (I think) electrical prongs on the motor drive. The drive screw will jump. Turn off motor drive, reattach to camera. Pray it works.
  Reply With Quote

Old 4 Weeks Ago   #5
wwfloyd
Registered User
 
wwfloyd's Avatar
 
wwfloyd is online now
Join Date: Jan 2019
Posts: 126
Heh, I'd had a want (not need) for an MD12 for my FE. Now, I can move on to want something else.
  Reply With Quote

Old 4 Weeks Ago   #6
Godfrey
somewhat colored
 
Godfrey's Avatar
 
Godfrey is offline
Join Date: Dec 2011
Posts: 9,138
I used an FM, FM2n, and FE2 with the MD-12 for many years without any problems at all. Never owned an FE, however.

The FE and FM first shipped with the MD-11 which, though very similar to the MD-12, might actually work a tiny bit better with the FE. The MD-12 was released with the later model FE2 and FM2 bodies.

Most problems like you report, however, tend to be some corrosion on the contacts ... either on the camera body, on the drive unit, or internal to the drive unit. I would certainly clean *all* the contacts and battery connections thoroughly, and put fresh batteries in both camera and drive unit.

G
  Reply With Quote

Old 4 Weeks Ago   #7
rulnacco
Registered User
 
rulnacco is offline
Join Date: May 2009
Location: London, UK
Posts: 139
Yeah, that can be an occasionally dodgy combo--I use it myself every now and again.

A couple of things:

You might want to make sure all the contacts inside the MD-12 and on the bottom of the FE are clean. Particularly if a battery has ever leaked inside the MD-12, you may have a bit of corrosion/oxidation in there. The best cleaning option is possibly one of those glass-fiber contact brushes (this, or something similar). Or you could carefully apply a bit of Deoxit spray; just don't let it run down inside the mechanism.

Another thing, the motor drive occasionally gets out of sync with the state of the camera's drive train. Take the motor drive off the camera, and make sure the camera is wound on and firing properly. Then take a quarter and lay it across all four contacts on the MD-12 simultaneously, with the drive turned on. That should short the terminals and cause the drive to cycle, hopefully ending up in the proper position in the cycle. Then put it on the camera and see if everything is synced up.

And of course, make sure your batteries are fresh as possible. The motor draws a pretty high current when it's cycling, and batteries that may be perfectly fine for many low-drain uses may not provide enough peak current to get the drive to work properly snappy, which could lead to problems.

Finally, if none of the above works, chuck out your MD-12 and buy a new one. They're plentiful and cheap, no reason to get frustrated over one that's basically knackered.

My FE and MD-12 work together swimmingly more often than not, and when they do, you can definitely get your old-school photojournalist groove on. But having dealt with them myself, I know how frustrating the problems with that combo, when they arise, are. Hopefully amongst me and everyone else, someone will provide enough info to sort yours out.

By the way, if you love your FE like I love mine, one of my favorite tips is this: get you a K3 screen (intended for the FM3a) and put it in your FE. It's much brighter (you *might* have to adjust exposure a bit) and it snaps into focus much better than the original screen in the camera. Makes a pleasurable shooting experience even better.
  Reply With Quote

Old 4 Weeks Ago   #8
Graham Line
Registered User
 
Graham Line's Avatar
 
Graham Line is offline
Join Date: Jan 2005
Location: Pacific Northwest US
Posts: 970
Secret seems to be never separating the drive from the body once everything is working.
__________________
My Gallery

My Flickr

You can join Visionless Hacks

I've been forty years discovering that the queen of all colors is black. - Henri Matisse
  Reply With Quote

Old 4 Weeks Ago   #9
Ste_S
Registered User
 
Ste_S is offline
Join Date: Aug 2017
Posts: 205
Quote:
Originally Posted by wwfloyd View Post
Heh, I'd had a want (not need) for an MD12 for my FE. Now, I can move on to want something else.
When they're working they're a really nice combo if you don't mind the weight.

Thanks for all the response and suggestions. I've had problems previously where the FE and MD12 lose sync, and this isn't that.
I suspect I need to get to why the meter needle isn't flicking on with the motor drive connected - normally it flicks on straight away when the unit is powered on, and half press on the MD12 shutter button wakes the meter up after going into stand by.

So contact cleaning, change batteries, short terminals to reset and then see I guess. If still not working time for another one...
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -8. The time now is 13:43.


vBulletin skin developed by: eXtremepixels
Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

All content on this site is Copyright Protected and owned by its respective owner. You may link to content on this site but you may not reproduce any of it in whole or part without written consent from its owner.